Log in
LEED v4
Healthcare
Materials and Resources
PBT source reduction - lead, cadmium and copper

LEED CREDIT

Healthcare-v4 MRc6: PBT source reduction - lead, cadmium and copper 2 points

LEEDuser’s viewpoint

Frank advice from LEED experts

LEED is changing all the time, and every project is unique. Even seasoned professionals can miss a critical detail and lose a credit or even a prerequisite at the last minute. Our expert advice guides our LEEDuser Premium members and saves you valuable time.

Credit language

USGBC logo

© Copyright U.S. Green Building Council, Inc. All rights reserved.

Requirements

Specify substitutes for materials manufactured with lead and cadmium, as follows.

Lead
  • For water intended for human consumption, specify and use solder and flux to connect plumbing pipe on site that meets the California AB1953 standard, which specifies that solder not contain more than 0.2% lead, and flux not more than a weighted average of 0.25% lead for wetted surfaces. The “lead free” label as defined by the Safe Drinking Water Act (SDWA) does not provide adequate screening for the purposes of this credit because the SDWA defines “lead free” as solders and flux containing 0.2% lead or less.
  • For water intended for human consumption, specify and use pipes, pipe fittings, plumbing fittings, and faucets that meet the California law AB1953 of a weighted average lead content of the wetted surface area of not more than 0.25% lead.
  • Specify and use lead-free roofing and flashing.
  • Specify and use electrical wire and cable with lead content less than 300 parts per million.
  • Specify no use of interior or exterior paints containing lead.
  • For renovation projects, ensure the removal and appropriate disposal of disconnected wires with lead stabilizers, consistent with the 2002 National Electric Code requirements.
Lead used for radiation shielding and copper used for MRI shielding are exempt.
Cadmium
  • Specify no use of interior or exterior paints containing intentionally added cadmium.
Copper
  • For copper pipe applications, reduce or eliminate joint-related sources of copper corrosion:
    • use mechanically crimped copper joint systems; or
    • specify that all solder joints comply with ASTM B828 2002, and specify and use ASTM B813 2010 for flux.
See all forum discussions about this credit »

What does it cost?

Cost estimates for this credit

On each BD+C v4 credit, LEEDuser offers the wisdom of a team of architects, engineers, cost estimators, and LEED experts with hundreds of LEED projects between then. They analyzed the sustainable design strategies associated with each LEED credit, but also to assign actual costs to those strategies.

Our tab contains overall cost guidance, notes on what “soft costs” to expect, and a strategy-by-strategy breakdown of what to consider and what it might cost, in percentage premiums, actual costs, or both.

This information is also available in a full PDF download in The Cost of LEED v4 report.

Learn more about The Cost of LEED v4 »

Documentation toolkit

The motherlode of cheat sheets

LEEDuser’s Documentation Toolkit is loaded with calculators to help assess credit compliance, tracking spreadsheets for materials, sample templates to help guide your narratives and LEED Online submissions, and examples of actual submissions from certified LEED projects for you to check your work against. To get your plaque, start with the right toolkit.

Get the inside scoop

Our editors have written a detailed analysis of nearly every LEED credit, and LEEDuser premium members get full access. We’ll tell you whether the credit is easy to accomplish or better left alone, and we provide insider tips on how to document it successfully.

USGBC logo

© Copyright U.S. Green Building Council, Inc. All rights reserved.

Requirements

Specify substitutes for materials manufactured with lead and cadmium, as follows.

Lead
  • For water intended for human consumption, specify and use solder and flux to connect plumbing pipe on site that meets the California AB1953 standard, which specifies that solder not contain more than 0.2% lead, and flux not more than a weighted average of 0.25% lead for wetted surfaces. The “lead free” label as defined by the Safe Drinking Water Act (SDWA) does not provide adequate screening for the purposes of this credit because the SDWA defines “lead free” as solders and flux containing 0.2% lead or less.
  • For water intended for human consumption, specify and use pipes, pipe fittings, plumbing fittings, and faucets that meet the California law AB1953 of a weighted average lead content of the wetted surface area of not more than 0.25% lead.
  • Specify and use lead-free roofing and flashing.
  • Specify and use electrical wire and cable with lead content less than 300 parts per million.
  • Specify no use of interior or exterior paints containing lead.
  • For renovation projects, ensure the removal and appropriate disposal of disconnected wires with lead stabilizers, consistent with the 2002 National Electric Code requirements.
Lead used for radiation shielding and copper used for MRI shielding are exempt.
Cadmium
  • Specify no use of interior or exterior paints containing intentionally added cadmium.
Copper
  • For copper pipe applications, reduce or eliminate joint-related sources of copper corrosion:
    • use mechanically crimped copper joint systems; or
    • specify that all solder joints comply with ASTM B828 2002, and specify and use ASTM B813 2010 for flux.
See all LEEDuser forum discussions about this credit » Subscribe to new discussions about Healthcare-v4 MRc6